Search Results

THIS paper records the results obtained from operating medium-weight trucks on pneumatic tires, and points out the advantages and disadvantages experienced. An analysis is made of the claims advanced in support of the use of pneumatic tires. Certain items are specified which in the author's opinion require further development before a satisfactory solution can be reached.

THE approaching exhaustion of the petroleum supply, from which nearly all of the available internal-combustion engine fuel is produced, raises two vital questions, upon the answers to which will depend the future of the automotive industry. These are (a) what fuels are to be available, from the point of view of the engine designer and (b) how much transportation can be secured from the fuel used. It is not certain that satisfactory engines can be developed to handle a wider range of fuels than those used at present. It is therefore not clear whether the trend of development will be toward two or more different grades of fuel, or toward a single mixed fuel to be used in all engines ultimately designed to burn it.

THE rapid development of heavy-duty trucks and farm tractors has made it necessary for manufacturers of engines used in such automotive apparatus to face problems regarding which there is no past experience to fall back upon. The necessity in both types of engine for maximum strength in all parts carrying excessive loads constitutes a problem of great importance, but in addition to it are others of the proper utilization of fuels at present available, lubrication under excessive load conditions over long periods of time; and, of nearly as much importance, the relation of fuels to lubricants and the effect of fuels upon lubricants. Moreover, information is to be acquired regarding the value of prospective fuels as power producers, the effects they have upon engines, lubricants, etc., comparisons of cost and the like. The tests recorded in the paper were made in an endeavor to ascertain some of these unknown values.

THE ordinary governor used on trucks and tractors is essentially a one-speed device. It gives good results at one speed, but at higher speeds “hunting” develops and at lower speeds governing is less accurate. This is because the spring must be stiff enough for maximum speed, and hence four times stiffer than it should be for half speed. The paper shows by calculations and curves the best results that can possibly be obtained; also, curves from a test showing what results are actually obtained with one well-known governor. Two new types of governor are described; in which the position of the spring is varied for different speeds. Theoretical curves also are presented and the results of tests, indicating that the new types produce the same character of curve at 800 as at 1600 r.p.m.

The paper treats the subject of ability from the point of view of its relation to the present trend in motor-truck design, setting forth some of the fundamental considerations involved. An ability formula when applied to automotive vehicles is to determine a “factor of experience” from which engine sizes and gear ratios can be calculated. While passenger-car performance is measured in terms of speed and acceleration, the latter are not the most important considerations in motor trucks, the speed of which is limited by the use of a governor. Wind resistance also is negligible at truck speeds. Practically the only resistances to be overcome by a motor truck are road friction and the force of gravity. Both road and grade resistance are in direct proportion to weight carried and are usually expressed in terms of pounds per pound.

THE design of a modification of the Class B Government standardized truck engine is presented, the principal object being a saving in weight without sacrificing either durability or safety factors. The crankcase design is rigid, but the metal is distributed so that the weight will be a minimum. The crankshafts are made of chrome-nickel steel of an elastic limit of 120,000 lb. per sq. in., which further carries out the idea of durability with low weight. The connecting-rod length is slightly more than twice that of the stroke, and this, with light-weight pistons, obviates vibration, without adding weight to the engine on account of increased cylinder height. The flywheel and bell-housing diameters were selected with a view to securing enough flywheel weight for smooth running without increasing the engine weight materially. All-steel supports reduce breakage of arms to a minimum. The manifolds are carefully designed to give economical performance, even with low-grade fuels.

The author considers the adaptation of farming implements to the farm tractor the most important engineering problem confronting tractor manufacturers. The problems are intricate in their ramifications, all-inclusive in their scope and fundamental. They can never be solved by theoretical discussion and laboratory tests alone. Extensive field experiments are needed with the machines operated by the farmers themselves. It is the implement which does the work. The mold-board plow and the disk harrow are standard for soil preparation; the oscillating sickle, the reel and the knotter-head for harvesting; the revolving toothed cylinder and the oscillating rack for threshing. Power must be transmitted to these fundamental devices. The automotive tractor fills a place in the farm power field not successfully covered heretofore by any single prime mover.

In the past the majority of trucks have been equipped with wood wheels. These gave good service, but the results demanded under strenuous modern conditions seem, the author states, to make the substitution of steel wheels on medium and heavy-duty trucks imperative. Truck engineers and builders seem to recognize the fact, but to hesitate to make the change, chiefly because a metal wheel is somewhat higher in first cost and because some designs have not as yet rendered the service expected of them. The service return of metal wheels is given from the records and reports of the London General Omnibus Co. and the Fifth Avenue Coach Co., both of which use steel wheels exclusively. The added mileage is in excess of wood-wheel service and exceptional tire mileage is shown. The author states briefly the arguments for the hollow-spoke, hollow-rim, the hollow full-flaring spoke and the integral-hub metal wheels.

The necessity for a powerful heavy-duty truck with power transmitted through all four wheels was apparent shortly after the United States became involved in the war. An intensive study of the four-wheel-drive situation finally resulted in the design of the Ordnance four-wheel-drive truck and the modified form known as the artillery wheeled tractor. Seven factors influencing the preparation of the specifications are stated and discussed. The determination of proper gear ratios is analyzed. The considerations leading to the adoption of the universal-joint type of driving-shaft are mentioned and its application commented upon. Ten specific points of internal interchangeability of the mechanism are enumerated.

THE United States was practically unprepared in the field of military motor-transport at the beginning of the war. Due largely to the cooperation of the Society of Automotive Engineers and its members individually, this handicap was overcome and a position stronger in this respect than that of any of the other belligerents was attained. The early efforts and the cooperation between the Society and the various Government departments are described, especially with reference to the Quartermaster Corps which at that time had charge of all motor transportation. Regarding the Class B truck, it is shown that the Society acted as a point of contact between the various members of the industry and the War Department and, although not fostering any program or plan of its own, it was largely responsible for the success of the standardization program conceived and carried out by the Army.

The title of this paper fully indicates its scope. The author presents an intimate picture of conditions prevailing at the war front which affect the operation and maintenance of war trucks, and these two factors in turn indicate the trend that design should take. The training of the mechanical transport personnel of the Army is also gone into at some length. The English and American trucks used earlier in the war consisted of about nineteen different makes and forty-two totally different models, resulting in a very serious problem of providing spare parts and maintenance in general. In the British Army transportation comes under an Army Service Corps officer called the Director of Transport and Supplies. At the outbreak of the war these officers had had little mechanical experience, horses being employed principally. In the French Army motor vehicles were used to a greater extent before the war, under the artillery command.

The author, from a first-hand study of this engine in the laboratory of Professor Junkers, traces the progress of the developmental work, and discusses the methods of operating the engine, its present status, its application to airplanes, trucks and tractors, details of marine and stationary types, fuel, advantages of and objections to the double-piston construction, and describes at some length the various parts entering into the construction of this type of engine. In conclusion, he summarizes the fundamental advantages of the Junkers engine.

The author describes a number of detailed developments that took place during the working out of a line of worm-driven trucks. The details of front axle and steering parts are dealt with at length, the reasons for the final constructions being clearly explained and the constructions themselves well illustrated. Details concerning difficulty with the Hotchkiss type of drive on heavy trucks, troubles with drive-shafts and lubrication of the worm wheel are all covered thoroughly; spring-shackle construction and lubrication, radiator and hood mounting come in for detailed attention and the question of governors is interestingly covered. Brief reference is made to the influence of unsprung weight, the differences between truck and pleasure car practice in this respect being pointed out.

The author outlines the constructions that have performed cially that four-cylinder engines carried under a hood are the most satisfactory. The defects revealed by war service are given in considerable detail, the author finding that all of the trucks used had developed some weak point. Radiators and springs are specified as a general source of trouble. The author outlines a number of operating troubles developed under the existing conditions of operation and gives examples of the way these have been remedied. Considerable attention is paid to the methods of operating trucks away from made roads. The methods of fitting chains to the wheels, and the use of caterpillar attachments are described. Dimensions are given for bodies and a number of suggestions made as to their proper construction.

This paper is mainly an argument in favor of the use of large, single rear wheel truck tires instead of smaller dual tires. Although the practice of using large singles is comparatively new, the author gives the results of experience and research to show the advantages of the newer method of rear tire equipment. In developing his arguments in favor of single tires, the author goes into the history of dual tire application to show why it was necessary to use two tires in the earlier days of truck operation. As the necessity for increased carrying-capacity grew, tire manufacturers found the then existing single tire equipment inadequate, and they set about to develop suitable equipment to meet the new condition, the result being dual practice. The method of attaching the earlier dual tires is shown to have been poor, resulting in circumferential creeping of the whole tire to a much greater extent as the width of the dual equipment increased.